SmartgridOne logo
SmartgridOne logo
Akcesoria
AplikacjaCertyfikatyCzas reakcji sterowaniaDioda stanuInformacje dotyczące bezpieczeństwa, konserwacji i prawneInstalacja
Konfiguracja od A do Z
KontrolerLicencja
Rozwiązywanie problemów
Samouczki wideoSieć
Skrzynka narzędziowa
Specyficzne dla klienta
Specyfikacje
Sygnały zewnętrzne
Szybki start
Urządzenia
Chmura
Falowniki hybrydowe PV i baterii
a-TroniXABB, FIMERADS-TecAforeAlphaESSAmpowrAngileAPsystems
Autarco
Bateria AtepsBeauventC-BateriaCellpowerChisageDanfossDeltaDEYEDiehl-AkoDynessDysun EnergyEcosourcenEenovanceElecnovaEnbrilionEnergreenEnerlutionEnjoyPowersEnphaseEVEFalowniki Anklous PV, hybrydowe i bateryjneFalowniki DET Power PV, hybrydowe i bateryjneFalowniki DMEGCFalowniki ESYFortona
Foxess
FraxFroniusGoodWeGotionGreener / Alfen
Growatt
HiteHithium
Huawei
Hypontech
Hyxipower
All In One ESSHybrid Inverters
iWellJinkoKacoKehuaKostal
Kstar
MarstekMastervoltMidTeQMotomaOctave EnergyOmniPowerPixiiPower-SonicPoweroadPylontechRegitecRenonRenowacjaRitarSAJSchneider SunEzySchucoSCUSE2200H do SE6000HSessySigenergySinexcel
Sma
Socomec
Sofar
Solaredge
SolarlogSolarMaxSolarwattSolaxSolinteg
Solis
SolplanetSprzęt EP
Sungrow
SunwaytechSunwoda
Sunwoda
Sus-PowerTeclomanTeploreTesvoltVaconVictronVolstoraWattsNextWeihengXantrexZendure SolarFlowZeversolar
Kocioł
Licznik energii
Licznik gazu
Licznik wody
Nowe integracje
PLC
Pompa ciepła
Przełączane obciążenia
Stacja ładowania pojazdów elektrycznych
Wytyczne dotyczące okablowania i łączności
UrządzeniaFalowniki hybrydowe PV i bateriiHyxipower
logo

Obsługiwane urządzenia

Device TypeVariantsManualModbus TCP (Ethernet)RS485Curtailment
All In One ESSHYX-H6K-HTAManual❌✅✅
HYX-H9K-HTA
HYX-H12K-HTA
HYX-H15K-HTA

Okablowanie

Hyxipower

Previous Page

Hybrid Inverters

Next Page

On this page

Obsługiwane urządzeniaOkablowanieRS485
RS485

Do okablowania RS485 użyj portu COM (nr 5) na falowniku.

Informacja
RS485 Wiring
  • For correct RS485 wiring: Follow the guidelines for RS485 wiring.
  • If the wiring shown in the table below is incorrect, please let us know.
  • There is no general consensus in the industry about the usage of A and B for the RS485 polarity, so it may be counterintuitive and opposite of what you might expect for some devices.
DeviceSmartgridOne Controller model OM1SmartgridOne Controller model IG8RS485-USB converterRS485-Ethernet converter
RS485 A (Pin 5)RS485 ARS485_POSRS485 ATX+
RS485 B (Pin 6)RS485 BRS485_NEGRS485 BTX-
N/ARS GNDGNDNot availableG
Ostrzeżenie
NOTE: RS485 Device Addresses
  • You MUST give each device on the RS485 bus a unique address. Check the manual of the device on how to do this.
  • Use lower addresses first (1, 2, ...) because the SmartgridOne Controller will find them faster!
  • For each device, it is generally recommended to stick with the factory default baud rate, parity, and stop bits. The SmartgridOne Controller will scan on those first.